Comparative Analysis of Heat Transfer of Engine Fins with different Materials in Steady State Condition

Aman Lahre, Snehlata Kanwar, Merkhapunp Bara, Manisha Usendi, Chandra Prakash Dewangan
Journal of Thermal and Fluid Science
volume 4: Issue 1, Jan-June 2023, pp 40-45

Author's Information
Chandra Prakash Dewangan 
Corresponding Author
Department of Mechanical Engineering, Government Engineering College, Raipur, Chhattisgarh 492015, India
cdewangan147@gmail.com

Aman Lahre, Snehlata Kanwar, Merkhapunp Bara, Manisha Usendi
Assistant Professor, Mechanical Engineering, Parul University, Vadodara, Gujarat, India

Article -- Peer Reviewed
Published online – 26 June 2023

Open Access article under Creative Commons License

Cite this article – Aman Lahre, Snehlata Kanwar, Merkhapunp Bara, Manisha Usendi, Chandra Prakash Dewangan “Comparative Analysis of Heat Transfer of Engine Fins with different Materials in Steady State Condition ”, Journal of Thermal and Fluid Science, RAME Publishers, vol. 4, issue 1, pp. 40-45, 2023.
https://doi.org/10.26706/jtfs.4.1.icramen202313

Abstract:-
Low Calorific Value (CV) coal is used in large quantity as compared to High Calorific Value coal in Cogeneration Power Plant (CPP) at Gayatrishakti Paper & Board Limited Unit-1, Vapi. But the moisture content in Low CV coal is very high about 35% - 45% (wet basis) which is not acceptable due to sticky property of coal, hence leads to increase in operation and maintenance costs attributed to handling of wet coal. So drying of coal is necessary to use Low CV. The drying performance of Low CV coal particle in laboratory scale with and without vibration assisted fluidized bed dryer was investigated under various operating condition: Inlet air temperature (60 - 80℃), superficial air velocity (0.14 – 0.43 m/s), bed height ( 20-60 mm), particle size (1-2,2-3,3-5 mm), frequency (110 - 340 Hz). The drying results shows that the moisture content with respect to time decreases with an increase in temperature, air velocity, and vibration frequency, and also increases with an increase in bed height and particle size.
Index Terms:-
Thermal conductivity, Heat transfer, Aluminum nitride, Zig zag fins, ANSYS2023 R1, Heat flux..
REFERENCES
  1. L.Prabhu, M.Ganesh Kumar, Prashanth M, Parthasarathy M, Design and Analysis of Different Types of Fin Configuration Using ANSYS, 2018.
  2. Hirenkumar A Patel , Vinamra S Kale, Sanjeev U Joshi ,Comparative Thermal Analysis of Fins, 2018.
  3. Rakesh Ramesh Poojari, Sandeep Pawankumar Sharma, Akash Anil Deore, Rahid Riyaz Kazi, Sagar dinkarVibhute, Thermal Analysis of Fins, 2018.
  4. Sujan Shrestha, Nitesh Kumar Yadav, Suman Bikram Bam, Analysis of Heat Transfer Through Fins of IC Engine, 2019.
  5. Pooran Singh Dhkar, Heat Transfer Analysis between Plate Fins and Pin Fins Using ANSYS, 2019.
  6. T R Chinnusamy , E Balaji , V Vignesh, T Karthikeyan , M Krishnan , Design Analysis of Cooling Fins for Two Wheeler Using ANSYS, 2019.
  7. Rajat Kumar , Devendra Singh , Ajay Kumar Sharma, Static Tharmal Analysis of Fins Models Using ANSYS, 2020.
  8. Kota LeelaSaiBharath, V Pradeep Kumar, Design and Analysis of a Rectangular Fin with Comparing by Varying Its Geometry and Material ,With Perforation and Extension, 2021
  9. Adil Abbas Mohammed, Performance of Rectangular Pin -Fin Heat Sink Subject to Impinging Air Flow, 2021.
  10. Mr. K. Manikandan ,S. Thirumoorthi, S.J. Sabharinaath, R.Sugumar ,P. Sabareswaran, Design and Analysis of Fins Using Various Configuration, 2021.
  11. Shankar Durgam , Aniket Kale ,Nikhil Kene, Akshay Khedkar ,SanketPalve and Nikita M. Gawai, Thermal Analysis of Fin Material for Engine Cylinder Heat Transfer Enhancement, 2021.
  12. Ambrish Pandey , Vikash Dwivedi To Investigate Optimum Design of Fins Model for Better Heat Transfer by Using ANSYS Software, 2021.
  13. K. N. Sai Sharan, Rohan Kumar Malla, Dr.P. Ravikanth Raju ,Kotha Nikhil ,Venkataraman Radha Krishan, Modeling and Analysis of IC Engine Fins by Using Different Materials, 2022.
  14. P.V. Ananth Subray , B. N. Hanumagowda , S. V. K. Varma , A. M. Zidan , Mohammed KbiriAlaoui , C. S. K. Raju , Nehad Ali Shah and PremJunsawang ,Dynamics of Heat Transfer Analysis of Convective -Radiative Fins with Variable Thermal Conductivity and Heat Generation Differential Transformation Method, 2022.
  15. Sandeep Gupta , Dheeraj Kumar ,Shailendra Kumar, Heat Transfer Analysis of Engine Cylinder Fins by Varying Geometry, 2022.

    16. To view full paper, Download here


For authors

Author's guidelines Publication Ethics Publication Policies Artical Processing Charges Call for paper Frequently Asked Questions(FAQS) View All Volumes and Issues

Publishing with