Design and Analysis of a Vertical Pressure Vessel with Effect of Rotational Velocity on the Stresses and Deformation by using ANSYS
Abdulfatai, A. Faro, Kazeem, K, Salam, Edith, E. Alagbe
Volume 6: Issue 3, Sept 2019, pp 110-120
Author's Information
Kazeem, K1
Corresponding Author
1Ladoke Akintola University of Technology (LAUTECH), Department of Chemical Engineering, P.M.B. 4000, Ogbomoso. Oyo State. Nigeria
kaykaysalam@gmail.com
Abdulfatai, A. Faro1
1Ladoke Akintola University of Technology (LAUTECH), Department of Chemical Engineering, P.M.B. 4000, Ogbomoso. Oyo State. Nigeria
Edith, E. Alagbe2
2Convenant University, Department of Chemical Engineering, KM. 10, Idiroko Road, Canaan Land, Ota, Ogun State.
Abstract:-
In this study, the suitability and influence of Rotational Velocity (RV) on the operating conditions of a vertical Pressure Vessel (PV) was investigated. A vertical PV was designed and analyzed with the aid of ANSYS. Effect of eight different parameters on the performance of the designed PV was analyzed. The results obtained from designed PV using Finite Element Analysis (FEA) was validated by comparing it with that obtained from Manually Computed Method (MCM) and Utilization Factor (UF) method. The results of this investigation show that the designed PV was safe within the specified operating condition, the FEA results are more accurate than that of MCM and presence of RV affected the stress distribution and deformation of the PV.Index Terms:-
Vertical pressure vessel, ANSYSREFERENCES
[1] K. S. Naser, Mohammed Q, and Gupta, “Structural & Thermal Analysis of Pressure Vessel by using Ansys,” Int. J. Sci. Eng. Technol. Res., vol. 2, no. 8, pp. 740–744, 2013.[2] I. Satyanarayana and K. Praveena, “Design And Analysis of the Pressure Vessel by using FEM,” Int. J. Innov. Sci. Eng. Technol., vol. 3, no. 10, pp. 145–150, 2016.
[3] P. Sadanandam, U. Ramesh, and S. Tamerat, “Design and Analysis of Pressure Vessel Using Finite Element Method,” Int. J. Latest Technol. Eng. Manag. Appl. Sci., vol. 6, no. 5, pp. 1–3, 2017.
[4] V. V Wadkar, S. S. Malgave, D. D. Patil, H. S. Bhore, and P. P. Gavade, “Design and Analysis of Pressure Vessel Using ANSYS,” J. Mech. Eng. Technol., vol. 3, no. 2, pp. 1–13, 2015.
[5] V. Khobragade, Rashmi and Hiwase, “Design , And Analysis of Pressure Vessel with Hemispherical and Flat Circular End,” Int. J. Eng. Sci. Comput., vol. 7, no. 5, pp. 12458–12469, 2017.
[6] A. Ibrahim, Y. Ryu, and M. Saidpour, “Stress Analysis of Thin-Walled Pressure Vessels,” Mod. Mech. Eng., vol. 5, pp. 1–9, 2015.
[7] J. Z. Li, “Computer Aided Modeling and Simulation of Structural Pressure Vessel Material Computer Aided Modeling and Simulation of Structural Pressure Vessel Material Performance,” in 2012 International Conference on Structures and Building Materials, 2012, pp. 1–10.
[8] O. T. Askestrand, Frode T and Gudmestad, “A Comparison Study of Pressure Vessel Design using Different Standards,” in 32nd International Conference on Ocean, Offshore and Arctic Engineering (OMAE2013), June 9-14, Nantes, France, 2013, no. June, pp. 1–15.
[9] ASME, “An International Code-2010 ASME Boiler and Pressure Vessel Code Section VIII,” 2010.
[10] F. Vakili-tahami, S. S. Sharifi, P. Majnoun, and A. Abbasi, “Calculating the Creep Life of Rotating Cylindrical Pressure Vessels by Reference Stress Method ( RSM ),” pp. 1–18, 2015.
To view full paper, Download here
To View Full Paper
For authors
Author's guidelines Publication Ethics Publication Policies Artical Processing Charges Call for paper Frequently Asked Questions(FAQS) View all Volumes and IssuesPublishing with
